Custom Step Alerts
Custom Step Alerts chain several conditions into one sequenced trigger: the alert only fires when your steps happen in the order you defined, inside a bar limit you set.
A single event tells you very little on its own. An AlphaWave flip followed by a pixel retest inside the OTE zone tells you that the new trend was confirmed by structure — and that is the kind of sequence this engine is built to capture.

In the example above the sequence is Reversal Sweep on step 1 and AlphaWave Trend on step 2, with the bar window set to 10. The sweep marks the exhaustion, the trend flip confirms it, and the tracker at the bottom of the chart shows the window between the two steps.
Setup controls
- Use Custom Alerts — turns the whole sequence engine on or off.
- Max Bars allowed between steps — the countdown. Once step 1 fires, the engine starts counting bars; if the next step does not happen within that window, the sequence resets to step 1.

Steps 1 to 5
Every condition is assigned a step number between 1 and 5. That number is what turns a list of conditions into a sequence.
- Sequential steps — different step numbers run in order. Step 2 must arrive on a later bar than step 1 before the sequence moves forward.
- Simultaneous steps — the same step number means both conditions have to hit on the exact same candle to satisfy that step.
Six conditions are available, each with its own step field:
| Condition | What it fires on |
|---|---|
| AlphaWave Trend | Any trend flip, bullish enter or bearish exit |
| AlphaWave Retest | Any, bullish or bearish retest of the wave |
| Pixel Flip | Any flip, pixel bull flip or pixel bear flip |
| Pixel Retest | Any, bullish or bearish pixel retest inside the OTE zone |
| Reversal Signal | Any, bull or bear reversal |
| Reversal Sweep | Any, bull or bear sweep of an invalidation level |
External source conditions
Three external sources let you pull other series into the sequence — another indicator, a moving average, price itself.

| Setting | Description |
|---|---|
| Source | The series that is evaluated. |
| Condition | Equal, Greater Than, Less Than, Crossing Over, Crossing Under, Crossing, True or False. |
| Comparison target | The value the source is compared with. Not used by True or False. |
| Step | Which step of the sequence this source belongs to. |
Selecting True or False turns the source into a binary condition, which is how you require a state ("price above the 200 EMA") rather than an event.
Time filter
Enable Time Filter restricts the whole sequence to a session window, with its own timezone — the
default is 1600-0100 on UTC+4, which is the New York session in Dubai time. Any step that fires
outside the window is ignored, so an overnight sequence cannot complete before you are watching.

How to create a Custom Step Alert
Turn the sequence engine on
Check Use Custom Alerts and set Max Bars allowed between steps — 20 bars by default. Until the engine is on, the condition dropdowns are only display filters and no sequence is tracked.
Assign the steps
Move every condition you want to use from Disabled to its event, then type a step number next to it. In the example at the top of this page Reversal Sweep is set to a bull sweep on step
1and AlphaWave Trend to a bullish enter on step2, so the trend flip only counts once a sweep has already opened the window. Anything you leave on Disabled is ignored by the sequence.Add outside filters (optional)
Enable any of the three external sources, pick the series, choose the condition, type the comparison value and give it a step number.
Restrict the sequence to a session (optional)
Enable Time Filter, set the session window and pick the timezone.
Create the alert in TradingView
Press Alt + A (or the clock icon in the right toolbar) and configure the dialog:

Market Waves PRO+ with the Custom Alert() option selected in the second dropdown - Condition:
Market Waves PRO+ - Second dropdown:
Custom Alert() - Trigger: once only, so the alert keeps watching for new sequences
- Name / Message: name the alert after the sequence it watches, and write a message that tells you which sequence completed.
Create the alert once. The engine now watches for your steps and fires when the whole chain completes inside the bar window.
- Condition:
Settings
| Settings | Description |
|---|---|
| Use Custom Alerts | Enable the multi-step sequence engine. |
| Max Bars Between Steps | Bars allowed between two steps before the sequence resets. |
| Module rows | Condition plus step number for AlphaWave, Pixel, reversals and sweeps. |
| External Source 1 / 2 / 3 | Source, condition, comparison target and step for outside series. |
| Enable Time Filter | Limit the sequence to a session, with its own timezone. |


X
Discord
Instagram
YouTube